Wireless Penetration Testing Guide Part 1: Intro and Basics

Arrow

Penetration Testing

Wireless Penetration Testing Guide: Part 1 – Intro and Basics

 

Regardless if you work in Security, Compliance, IT, or management, it is a near 100% chance that you have encountered wireless networks in the enterprise before. Wireless networking has been around for quite some time and -in my experience- are given less consideration when it comes to configuration, deployment, and most importantly security. This is a problem, as a compromise of a company’s wireless network usually means access directly to the backbone of an organizations internal network and resources, among other things. This guide will take you through the how’s and why’s of wireless, in addition to teaching all of the most common (and some lesser known) attack vectors. We will also be covering Bluetooth, NFC, and some hash cracking in order to obtain a broader understanding and more effectively attacks against wireless systems.

image1
 

Firstly, let’s start off strong with a brief overview of the fundamentals of wireless network communications. Now I can understand that this part might be a bit dry, but it is definitely necessary to a full understanding of “the big picture”. In addition, I know that some of our readers might already know what is in this section, but a brief refresher never hurt anyone.
 
In general, there are 2 components to a basic wireless network; the Access Point (Referred to as the AP), and the client. The client and the access point create a connection between each other, and send each other wireless signals (Most commonly over 2.4 and 5Ghz) that are then interpreted on each end. These signals encapsulate packets and have a fixed structure that is dependent on the protocols that are used for that specific sort of communications. The AP then interprets these signals and (in most cases) converts them to regular network traffic, that is then either routed to other wireless clients, or back into the network that the AP is connected to.

image2

 

Now, with all of this data going over the air, anyone in range would be able to view and modify this traffic. That’s why different encryption methods have been devised to protect this traffic that is otherwise viewable by anyone with a good antenna and a bit of luck. A few of the most common encryption types are WPA, WPA2 (And variants), and WEP.

image3
Source: https://wigle.net/
 

As you can see in the above graphic, over time there has been a shift in what protocols are used. In the infancy of wireless, there were only open (unencrypted) wireless networks, and WEP encrypted wireless networks, but as time went on, WPA and WPA2x gained popularity for reasons of security. In an open wireless network, any client can connect (also known as “associate”) with the wireless network as long as they are in range. In addition, even if a client is not associated with an open AP, they would still be able to see all traffic going over the air in essentially plain-text (when using special hardware detailed in pt. 2).
 

In an encrypted wireless network, the connection between the client and the AP is secure in the sense that an outside onlooker, who does not have access to the wireless network (usually through password based authentication) would not be able to view and/or modify the traffic of the clients of that specific network. The first standard form of this type of encryption was called “WEP” (Wired Equivalent Privacy). For some time, WEP was known was the de-facto method for wireless security, until tools, attacks, and methods where developed essentially making this sort of authentication useless. In modern wireless networks, much more sophisticated WPA and WPA2x security is used to better protect these networks. Although these encryption protocols are strong, they all have weaknesses that can be exploited in order to gain access to the AP, Client, or underlining network.
Now, it is not just the security of the wireless protocol itself that is important, but what those wireless clients have access to. For example, in a typical home network, the entire wireless and wired network are on the same subnet, and thus a client on the AP can have access to a smart TV hooked up by Ethernet. In addition, home networks usually have WPA/WPA2-PSK encryption that only involves a password for authentication.

 

Conversely, in the enterprise, it is best practice to isolate the wireless networks from the rest of the company’s internal network, and only allow wireless clients to access parts of the network on a case-by-case basis. This is called “wireless isolation” and is commonplace in the modern enterprise system. Although it is the better option, a lot of company networks fall victim to negligence during wireless configuration, thus a wireless client will have access to the internal network. This is fantastic from a would-be attacker standpoint, as the wireless network now becomes a more lucrative point of entry. Additionally, in an enterprise, it is possible that the wireless networking system has added layers of security. An example of this would be “Mac address whitelisting”. This is when only a predetermined set of clients are allowed to connect to the AP. The MAC address is data that is unique to the specific wireless adapter installed on a device (i.e. a laptop wireless card, a USB wireless card, a cell phones internal wireless adapter.). Another example would be username/password authentication that could authenticate the user with a Radius, MS Active Directory, or other server.

 

Now that we have a solid understanding of the basics of these types of networks, we can move on to learning about their vulnerabilities and how to exploit that, and the first thing we need to cover is hardware. What exactly you are going to need to get going with wireless penetration testing, from a basic USB card to a 2 mile+ packet cannon, this will all be covered in part 2 coming shortly.

Stay tuned at https://www.linkedin.com/company/virtue-security

Mark Shasha is a penetration tester at Virtue Security in New York City – @bignosesecurity

More posts like this can be found at Virtue Security.

This is a Security Bloggers Network syndicated blog post authored by Mark Shasha. Read the original post at: Virtue Security